Hydraulic
details
Gerobox produced by ZF and hydraulic pump from
Rex Roth G-90 German-made model and hydraulic motor from
Produced by Rex Roth
* Turkish-made operating farmer
* Wire Operating Turkish Made
Products
Balloon "Drama"
details
- External body factory of solid 5.5mm corrosion resistant.
- Introduction 8mm thickness balloon and 5mm inner feathers
- Penis Diameter 170cm Thickness 60mm Chemically and Thermally Treated Steel
Diameter 180cm 8mm thickness contains 24mm 16mm stiff thickness of 40mm bottom screws with braces to reduce load and not rely solely on the welding line for power transition between gearbox and bottom
Water tank
details
Water tank capacity 900L, diameter 75cm and length 170cm
* The tank has a gate to periodically clean the tank which increases its life span
* The tank operates with a compressed air system which in turn works to rush water quickly and at high pressure
* The tank has a statement specifying the tank water level with a safety valve to release excess air pressure.
* The bottom of the tank is made of 6mm steel and the rest of the 5mm steel structure
* The tank has segments on the inside to increase support.
* The 1.5 inch diameter water line is made of 3.5 mm thickness steel with 2 inch diameter water charging link.
* Water tank charging hose, 1.5 inch diameter, can withstand the pressure of 25 bar made of Turkish-made tilt-backed kauch.
* Washing hose length 12 meters diameter 4/3 inches Italian made water line stretches inside the chassis to provide him with shock protection.
Gutter Holder
details
The lower stand: a 1.5-inch straight pipe, with a pair of pallets installed in the middle of it, each with clamps on one pallet, in contrast to the clamping on the other pallet, in order to make the necessary clamping to adjust the level of the funnel
The front chair
details
The chassis of the front chair consists of the chassis of the boxes 100 * 150, the thickness of which is 6 mm, and the rest of the front chair is of 6 mm steel. The upper plate of the front chair is of 12 mm steel, equipped with 2 heights of 30 mm
The fenders
details
Made of steel sheet 52, thickness of 2.5 mm, in order to reduce the load on pregnant women and ensure that no cracks occur due to the length of the planters and loading, in addition to the huge vibrations that farmers are exposed to as a result of bumps and potholes that the car encounters while driving.
The single fender is made of two parts in order to reduce the cost of repair in the event of a collision with the car "accident"
* The fenders are installed on three holders that take the shape of the flap from the inside. These holders are made of 1.5 inch 3.5 mm thick tubes that are attached to the chassis. To increase durability, each holder is reinforced with a pair of 6 mm thick screens cut as follows:
* The holder pipe with the fenders there is a slice of steel to ensure the largest possible space for installing the fenders.
Gutter connections: The mixer contains a pair of gutter connections, each one 1 meter long, 2.5 mm thick, each one stored on a dedicated base installed on the top of the fenders.
The lower stand: a 1.5-inch straight pipe, with a pair of pallets installed in the middle of it, each with clamps on one pallet, in contrast to the clamping on the other pallet, in order to make the necessary clamping to adjust the level of the funnel
Funnel spare parts
details
upper funnel
Made of two layers, each layer is 3.5 mm thick
* The inner layer is fixed with the funnel by a wide pinch length 5 cm
This is for ease of change after the expiry of the life span. The funnel is installed at an angle of inclination to fill the concrete in the middle of the drum, where the funnel extends to the third vane of the drum.
Funnel mounts: The upper mount is a 1.5 inch 3 tube with a center roll of 95 degrees, thickness of 6 mm, and a pair of laser perforated and rolled hooks on the sides.
Seven spare parts "Combined shot"
details
Seven: Combined shot The design is streamlined in the shape of the corner bomb, which works on sliding concrete The seven are made of 3.5 mm steel and the inner lining is 3.5 mm thick. The lining covers the discharge areas on the right and left, and the liner is fitted with a wide notch for easy changing.
gutter spare parts
details
Axial discharge gutter, width 85 cm, length 1.5 m, made of 3.5 mm steel and 3.5 mm liner
The back chair
details
Back seat of the suit “back camel”
Back Cardboard 150*100 Thickness 6mm Cardboard
Back seat inside 2 inside.
The unloading gutter holder has a pair of 45mm hinged joints that are attached to the seat back body.
the ladder
details
There are two models of ladder, the sliding ladder – the guillotine ladder, which is made of 3 mm thick pipes mounted on a 6 mm bracket, and the space for the ladder to stand is 40 cm / 75 cm.